Page 8 - catalog_manual

Finishing
Finishing
& Disposal

Post-press

Binding Binding ● Adhesive binding Adhesives Shopping Bag ● Side by Special Machine：Hot Melt or Solvent type
1) Perform deeper “roughing” than that for paper. ● By manual：EVA Emulsion or Double Face Tape
2) EVA hot melt is suitable as an adhesive. If the temperature of the hot melt ● Bottom by Special Machine：EVA Emulsion
®
is too high, YUPO may be affected by distortion, so use a setting of
around180°C.
★“Notch binding ／ burst binding”is very suitable Envelope EVA Emulsion or Double Face Tape
● Ultrasonic sealin
Used for jobs with few pages (Up to approx. 16P at 200μm). Memo Pad EVA Emulsion or Hot Melt
● Loose leaf
● Spiral wire binding Label for Glass EVA Emulsion (Strip Gluing is recommended) or Hot Melt
● Saddle stitching Bottle or Can

Cautions concerning Avoid using YUPO as a cover sheet or an inserted page if it is to be bound Poster EVA Emulsion or Double face Tape with thick adhesive layer.
®
binding (to Wooden board or Concrete)
together with ordinary papers as curling or distortion can occur.
Perfect Binding EVA Hot Melt
Grain direction Align grain direction parallel to vertical as for ordinary papers.

Laminating Wet Lamination Emulsion adhesive of Vinyl Acetate type or EVA type.

Disposing
Dry Lamination Solvent type adhesive or Reactive Adhesive. Disposing
®
material and can be safely incinerated ～
Trimming Guillotining 1. Always use a sharp blade. 3. Pile height of 15cm maximum is recommended. of YUPO š ～ YUPO is an environmentally friendly
®
2. Expel air from between the sheets. 4. For α YUPO ,keep the pile below 10cm.
Post-press
Die Cutting Corners should be round. Sharp corners could start a tear.
● Disposing and recycling
・When disposing of YUPO as ordinary household
®
Drilling 1. Sharp drill should be used. waste, be sure to follow the applicable local regulations
2. The maximum thickness of the pile is recommended to be 25mm. for disposing of plastics.
3. The intervals should be taken longer for drill to cool down.
®
4. Make sure to bleed the air out sufficiently before drilling. ・When processing YUPO as office waste, be sure
to process it as an industrial waste.
®
・When disposing of large amounts of YUPO , the
following reuses are possible.
®
1. YUPO is easily folded along the grain direction.
Folding 2. FPG95 is the most suitable grade for folding among YUPO grades. 【Reuse as a solid fuel】
®
3. Setting the Folding Machine. YUPO to be disposed of such as used pamphlets
®
1) Roll pressure should be set at the maximum. and the like can be reused as a resource for
2) Roll pressure should be set balanced evenly at both ends of a roll. thermal energy as a recycled plastic fuel (RPF).
®
3) YUPO should be exactly fed at right angle. The polypropylene resin used as a raw material
®
for YUPO consists of carbon and hydrogen, so
when incinerated with sufficient oxygen it becomes
carbon gas （CO 2） and water （H 2O） without
producing any chlorine gases or nitrogen oxide.
Perforation can run either with or across the grain, but its tearing Comparison chart for combustion
Perforating characteristics will differ so adjustments to the blade is necessary. 【Reuse as a recycled resin】 YUPO Approx about 7,200
®
● Across Grain Direction：Below 0.5mm ／ CUT…2 ～ 3mm Collected waste sheets and cutoffs can be reused Coal 8,000 to 8,500
● With Grain Direction：Below 0.8 ～ 1.0mm ／ CUT…2 ～ 3mm as a raw material for recycled resin products such Oil 9,600
as flowerpots, seedling trays, and stakes. Polyethylene 11,000 ※ Kcal/kg

13 14